A. It’s much easier to apply because of its smooth, creamy consistency and one-step application saves considerable time. Using this product eliminates the need to pre-wet the surface or stock up on the extra pails needed when you mix by hand. Apply to dry or slightly damp surfaces.
A. Rub your fingertips over the suspect area. If they are wet, do not paint the surface.
A. When applied according to directions, both DRYLOK® and Latex Base DRYLOK® are warranted for 10 years, but will provide many additional years of satisfactory performance.
A. Coverage per gallon is 75 to 100 square feet, depending on the porosity of the surface.
A. DRYLOK® Extreme and DRYLOK® Latex Base Masonry Waterproofers are not formulated for floors. You can use DRYLOK® Clear Masonry Waterproofer on floors and walls. It holds up to foot traffic as a finished coat and can be used before applying floor paint, or latex-based adhesives.
A. Yes and no. DRYLOK® may be used over any other cementitious-type waterproofing paint in good, repaintable condition, either inside or outside. However, DRYLOK® cannot be used over an oil or latex-based paint on the inside of a building. DRYLOK® will adhere to these paints, but if it cannot penetrate into the pores of the masonry itself, it will not waterproof the surface.
A. Yes and no, it can go on any properly prepared masonry surface that has a certain amount of porosity.
A. Yes, DRYLOK® Masonry waterproofer is ideal as a foundation waterproofing coating. Wait 24 hours after the application of the second coat to backfill.
A. Absolutely. In fact, DRYLOK® makes an ideal base coat. After applying DRYLOK®, wait at least 24 hours and then paint it with a good quality latex top coat.
A. Yes! Plus, in addition to being a terrific timesaver, DRYLOK® is available in a range of colors to help you add personality to your basement, workshop, laundry room, and other living areas. DRYLOK® Latex Base Masonry Waterproofer’s sandy finish is available in 4 ready-mixed colors (blue, white, gray, and beige) and 6 tints (buttercup, mint green, platinum, sand, slate blue, and soft pink). If you prefer a smoother finish, choose DRYLOK® Extreme Masonry Waterproofer, available in bright white and an expanded tint palette (beige, blue, buttercup, gray, mint green, platinum, sand, slate blue, and soft pink).
A. Yes, wait 24 hours to apply.
A. Use on surfaces, cracks in walls, pools, wall joints and affixing objects that will be subjected to applied pressure.
A. United Gilsonite Laboratories manufactures a product called DRYLOK® Etch. While DRYLOK® Etch will remove efflorescence and help prevent it from reoccurring, understand that efflorescence comes from salt deposits found in the block itself and can reoccur at any time.
A. DRYLOK® Concrete Protector has a curing compound and can be used on new concrete or old concrete to control dusting. It is a water sealer. DRYLOK® Clear Masonry Waterproofer stops water from coming up through the concrete floors. It is a waterproofer.
A. DRYLOK® Concrete Protector is a penetrating sealer for bare concrete. After application, wait 24 to 48 hours before painting with a latex or acrylic floor paint.
A. Use DRYLOK® Wetlook Sealer for a decorative high-gloss coat over floor paint.
A. Yes.
A. DRYLOK® Latex Masonry Waterproofer can be used to successfully waterproof fish ponds as long as the product is allowed to cure for the recommended 5-7 days. This cure time is necessary to ensure that all the volatile “processing aids” have completely evaporated from the dry film. Failure to allow for complete curing can cause excess foaming when water is added, and possibly even affect water quality.